Margot Machinery buys and sells used paper converting machinery: slitter rewinders, rewinders and unwinds, sheeters, core cutters and the presses and finishing equipment that run with them. Below is a selection of converting machines in stock now, followed by links to each machine type. Request a quote on any machine, or send your web width, basis weights and roll sizes to margotsales@margot.com and we will source one.
Used 82" PCMC two-position phantom-axis turret unwind, up to 48" max diameter, shaftless with 6" chucks, independent arms, regenerative drives, dual direction splicer, speeds up to 1800 FPM.
Used Black Clawson Turret Rewind. Equipped to handle 50" maximum diameter rolls, and equipped with 3" & 6" diameter air shafts, roll changer for automatic operation, operator console. two motors but no drives are included.
Used 88" Beloit Automatic Turret Rewind, a shaftless turret rewind good for 60" maximum diameter rolls
Used 60" Stanford 252 FW reversible salvage rewinder/doctor machine with 30" unwind and 30" simplex rewind (3" lug air shafts, rider rolls), Dynaweb dancer tension control with taper, Fife CDP-01 edge guide, razor-in-grooved-roll slitting, 2000 FPM, 20 HP Yaskawa V1000 drive, 460/3/60, Allen-Bradley MicroLogix PLC.
Used 63" W&H turret rewind equipped with 40" diameter maximum rewind, two 3" air shafts, automatic roll changer for continuous operation, control panel and operator interface attached to machine, no drives.
Used 16" Rotoflex model VIR400 reversible inspection rewinder with 36" maximum diameter unwind (6" cores), splice board with pneumatic clamping, E&L edge guide, Control Techniques drive, Guardstar light curtain safety system, 460V/3Ph/60Hz.
Used 16" Custom salvage rewinder equipped with 20" diameter cantilevered unwind with 3" chucks
Used Stanford model 142 LT doctor machine/salvage rewinder with 30" cantilevered unwind, Fife edge guide, razor-in-grooved-roll slitting, and 24" cantilevered rewind.
Used 67" Fischer & Krecke Turret Rewind, a non-stop automatic turret rewind good for maximum 67" wide by 40" diameter rolls
Used Appleton model 81010 core cutter for 120" x 3" diameter (ID) cores with pedal controlled cut and manual core advance.
Used 67" Fischer & Krecke Turret Unwind, a non-stop automatic turret unwind good for maximum 67" wide by 40" diameter rolls
Used 2500mm Laem duplex center slitter, upgraded by Siemens in 2022, with 1000mm shaftless driven unwind (75mm cores), 250mm minimum slit width, 1000mm rewinds with independent arms (75mm and 150mm cores), Siemens AC motors, ABB drives, Siemens PLC/HMI; runs BOPP, polyester, CPP film and paper; 650 mpm max speed.
The machines above are a selection from our converting inventory. Browse by machine type, or see the full converting machinery list.
Duplex center and center-surface slitters, simplex slitters, salvage and inspection rewinders, two drum winders.
Turret rewinds and unwinds, single and dual position stands, surface rewinds and accumulators.
Roll-to-sheet cutting for paper, board and laminates, with stackers and delivery tables where included.
Core cutters and paper tube equipment used alongside slitting and rewinding.
Flexographic and rotogravure presses and related print finishing equipment.
The complete converting machinery inventory, including other finishing and handling equipment.
Margot Machinery has bought and sold used converting equipment since 1993. Listings show the specifications we have confirmed, and machines marked In Operation are installed and can be inspected under power by arrangement.
If the machine you need is not in stock, send your requirements and we will search for it.
Request a QuoteEquipment that turns parent rolls of paper or board into finished rolls, sheets or cores: slitter rewinders, rewinders and unwinds, sheeters, core cutters, and the presses and finishing machines that run with them.
Machines marked In Operation are installed and can be seen under power by arrangement. For other machines we provide the photos, video and documentation we have on file.
Yes. We buy single machines and complete converting lines. Use the Sell Your Equipment form or call (518) 346-6379 with the make, model, width and location.
Rigging, loading and freight can be included in your quote. Tell us the destination and any dock or door constraints and we will quote the options.
Tell us the machine type, web width and grades you run. We will check our network and come back with options.
